Category: Front Porch Replacement

The first step in replacing the front porch is to take off the existing porch. I took off the roof of the porch a few years ago because it was too short to accommodate the new front door. Before I could take off the porch, I had to move the mailbox and our delivery bin. I mounted the mailbox to the fence by the front gate and put the delivery bin underneath it. Despite this, UPS is being difficult and doesn’t want to deliver now.

Old porch

The peeling paint on the porch made it look like it had been there for ages, but underneath it turned out that it was built not terribly long ago out of pressure-treated lumber. I took off the heavy wrought iron railings. I used an angle grinder to cut the ends off the concrete stoop. By the time I got the last piece out to the alley a scrapper was already loading the first ones onto his truck.

Removal in progress

The old porch used approximately 50% of the lumber it should have, with large spans between joists, stringers, and mediocre at best support. The porch itself came down in a couple of hours. The support posts had zero footings, and literally rested on the surface. I’m surprised it didn’t sink into the ground. It was a positive as far as I was concerned, because it made it that much easier to tear down.

Porch removed

What wasn’t so easy was the front stoop. The bottom step of the porch was a 16″ thick block of steel-reinforced concrete, and I declined to rent a demolition hammer, instead mostly relying on a sledgehammer and a prybar. It took far longer to break apart the stoop than the rest of the porch, and my hands still hurt days later. Bits of concrete flew into both neighbors yards as well as the sidewalk out front, so even once it was broken up I was still walking around picking up little pieces.

Breaking up the stoop

I’ll also need to take out the front sidewalk, but we’re planning to replace it with pavers. Since the main paver project will be in the back yard (some time in the future), for now we’ll just cut the existing sidewalk back to where it needs to stop and do all the pavers together (later). I haven’t done that part of the demo yet. I have to figure out how to run the 20-amp extension cord that the concrete saw uses to the front yard when it’s not long enough to reach the nearest 20-amp outlet.

With the bump-out gone, we’ve decided that the next project is to replace the front porch. Given the state of the house, this may seem a bit out of order, but as usual there’s a method to our madness. While we have a lot of work to do on the interior, we want to finish the exterior of the house so that we don’t wind up with (more) water damage on the inside, especially on new stuff we’re putting in. The top of that list is replacing the roof and fascia (we don’t have soffits). Before we can do that we want to take the hips off the gables, so we can put a bigger window in the front of the attic and a door at the back (fire code egress requirements). The new front porch will be covered, meaning it’s going to have its own roof and fascia. So the first reason to do the porch first is that it means we can get all of the roofing and fascia done at the same time. If we follow that on with the second floor windows and back door, we can also do the trim, siding, gutters, and downspouts, which would go a long way to improving our life in the basement, just from a humidity standpoint. Once the outside of the house is done, I can go back to the second floor and level the subfloor, replace the attic joists, and frame out the structure, walls, attic stairs, and so on.

House rendering with porch

The other advantage to replacing the porch first is that will work as scaffolding on the front of the house, where we have four very large windows to replace. By building the ceiling frame of the porch before the roof line, we’ll have a flat platform from which to rebuild the second floor bay, which uses the same decorative sheathing as the first floor and needs to be rebuilt before it can accommodate the new windows. Plus while we’re at it we can take off all the siding on the front of the house and the flashing details of the windows can be done correctly. So, in short the plan for the porch is to work our way up, building and taking off siding as we go. When the windows are replaced, we’ll finish the porch roof framing, and then get all of the roofing, trim, fascia, and siding done at once.

With that worked out, the first step to building the new porch (other than planning) is to take down the old one!